Home » Posts tagged "maintenance" (Page 2)

AMSOIL SYNTHETIC LUBRICANTS INCREASE FUEL ECONOMY 6.54 PERCENT

imageAMSOIL SYNTHETIC LUBRICANTS
INCREASE FUEL ECONOMY
6.54 PERCENT IN DIESEL
TRUCKING APPLICATIONS1

FREE Amsoil Catalog

For a copy of this study, ask for it in the catalog request form!

Use this link for all Amsoil heavy trucking products on one page.

Industry-Standard Testing

image

To determine the fuel economy benefits of its synthetic lubricants, Amsoil conducted the industry-standard SAE J1321 In-Service Fuel Economy Test Procedure.
First, the baseline rate of fuel consumption was determined for two nearly identical Kenworth® T800B diesel trucks and 53’ trailers from Ford® Motor Company’s* Rawsonville, MI fleet. Texaco brand conventional lubricants were installed in each vehicle’s engine, transmission, and front and rear differentials. Both trucks simultaneously completed runs on a 40-mile test route representative of real-world driving conditions beginning and ending at Ford’s Rawsonville fleet maintenance facility.
Fuel consumption was recorded from each vehicle’s engine control module (ECM)
following each run. Although both vehicles were operated using the same conventional
lubricants and according to the same procedures, the test truck consumed an average
of 0.37 more gallons of fuel per run compared to the control truck.

 

image

 

The test truck alone was then thoroughly flushed of its conventional lubricants prior to
installing AMSOIL synthetic lubricants. Both trucks simultaneously completed runs on
the test route according to the same procedures used during the baseline segment. Fuel
consumption data was again recorded from the ECMs. The switch to AMSOIL synthetic
lubricants eliminated the 0.37-gallon difference in fuel consumption per baseline
segment run, resulting in 6.54 percent improved fuel economy.

image

 

WordPress Tags: AMSOIL,SYNTHETIC,LUBRICANTS,INCREASE,FUEL,ECONOMY,PERCENT,benefits,industry,Service,Test,Procedure,consumption,Kenworth,Ford,Motor,Company,Rawsonville,fleet,Texaco,vehicle,engine,transmission,Both,world,maintenance,module,Although,procedures,truck,trailers,differentials,vehicles,trucks

Share
Posted on December 26, 2011 by , Reply

Synthetic Compressor Oil

Synthetic Compressor Oil – eliminate maintenance on compressors

Free Amsoil Catalog

synthetic compressor oil Buy Amsoil Synthetic Compressor Oil now!

Synthetic compressor oil can eliminate one maintenance chore in your shop. Most folks never change the compressor fluid in shop air compressors. These are often neglected, but critical tools in a shop. You can eliminate the need to maintain and monitor oil changes in compressors by installing synthetic compressor oil. AMSOIL PC Series Synthetic Compressor Oil is a long-life, premium compressor lubricant based on novel, proprietary technology. It incorporates the highest quality, thermally stable PAO synthetics fortified with premium non-detergent, ashless additives for maximum protection at high temperatures and pressures. It lasts up to eight times longer than petroleum oils, effectively reducing maintenance and waste oil disposal costs.

Improves Compressor Efficiency
AMSOIL PC Series Synthetic Compressor Oil has low friction properties and resists viscosity increase from oxidation. It helps improve operating efficiency and saves money on electrical energy consumption.

Synthetic Compressor Oil

synthetic compressor oilControls Foam and Reduces Wear
AMSOIL PC Series Synthetic Compressor Oil contains anti-foam additives and, unlike some other compressor oils, is anti-wear fortified. Good foam control reduces heat, oxidation and wear. High contact regions are protected against wear for increased compressor life and efficiency.

Resists Water Contamination
Water from condensation builds up in compressors and can cause unwanted oil/water emulsions, environmental discharge hazards and rust. AMSOIL PC Series Synthetic Compressor Oil is hydrolytically stable. It resists acid formation, readily separates from water and is anti-rust fortified. Water can be easily drained for simplified environmental discharge and increased oil life.

Resists Heat and Oxidation
AMSOIL PC Series Oil combines the inherent stability of premium synthetic base oils with specialized anti-oxidant additives to resist varnish, carbon and acid formation. It is formulated to protect compressors better and last longer in service than petroleum oils, especially during hot operating conditions.

Synthetic Compressor Oil

Safety Advantage
AMSOIL PC Series Oil is an ashless, high-flash-point formulation with very low carbon-forming tendencies that minimizes the incidence of ignition-promoting “hot spots.” While PC Series Oil can provide improved fire safety, it cannot be considered non-flammable.

Application Recommendation
AMSOIL PC Series Oil in the appropriate viscosity is recommended for use in single and multistage rotary screw, vane, centrifugal and reciprocating compressor crankcases and cylinders, vacuum pumps and other applications such as gears, bearings, blowers, pumps and handheld pneumatic tools. In compressor applications, drain intervals of 8,000 hours or more can be expected under normal operation. Drain intervals are subject to operating conditions and maintenance practices. Monitoring by oil analysis is recommended. For best performance when converting to AMSOIL PC Series Synthetic Compressor Oil, it is recommended the compressor be drained of the old fluid prior to the installation of PC Series Oil. If carbon deposits are present on the internal components, it is recommended they be removed following the compressor manufacturer recommendations.

How to change the air compressor oil

Some air compressors are oil less; they do NOT use oil. If you have one of those, you don’t have to change oil since there isn’t any. Most large shop style tower compressors ARE oil lubricated.

  • Do NOT use regular automotive oil; this is against almost all manufacturer recommendations. Read your manual.
  • Determine the weight and spec recommended.
  • There will usually be a drain and a filler/dipstick.
  • Drain the oil, and put the plug back in.
  • Fill the oil to the level recommended on the dipstick, or on the oil sight glass.
  • Most manufacturers (including CH) recommend changing once after the first hour of use.

  • Synthetic Compressor Oil

    Synthetic Compressor Oil

Here is a detail of how to read the oil sight glass;

Synthetic Compressor Oil

Synthetic Compressor Oil

 

COMPATIBILITY
AMSOIL PC Series Synthetic Compressor Oil is compatible with petroleum oils and most synthetic oils, seals, paints and materials, including the following:

Gases:

• Nitrogen • Hydrogen • Helium • Carbon Monoxide
• Carbon Dioxide (dry) • Ethylene • Methane
• Propane • Butane • Propylene • Butylenes
• Natural Gas • Benzene • Butadiene
• Furnace (crack gas) • Hydrogen Sulfide (dry)
• Synthetic Gas • Sulfur Dioxide

Paints:

• Epoxy • Oil Resistant Alkyd • Acrylic Enamel

Plastics:

• Acetal (Delrin) • ABS • Phenolic • Polyamide-imide
• Polyamide (Nylon)
• Polycarbonate (metal covered only)
• Polyester • Polyetherimide (Nylon) • Polyimide
• Polyphenylene oxide • Polystyrene • Polysulfone
• PTFE (Teflon) • Terephthalate.

Elastomers:

• Fluoroelastomer (Viton) • Nitrile (Buna N)
• Polyacrylate • TFE/P • Poly Urethane.

Note: Not recommended for “breathing air” or refrigeration compressors. Not recommended for use with polycarbonate plastic that is not metal covered, PVC plastic and butyl, ethylene-propylene or SBR rubber. PC Series Synthetic Compressor Oils are Not Compatible with polyalkylene glycol or silicone oils.

Synthetic PC Series Compressor Oils SAE 10W
(PCH)
 SAE 20
(PCI)		 SAE 30
(PCJ) 		SAE 40
(PCK)		 SAE 50
(PCL)
ISO VG – ASTM D-2422 32 46 68 100 150
VK 100°C – ASTM D-445 6.2 7.3 10.9 13.6 17.9
VK 40°C – ASTM D-445 33.1 42.4 67.4 100.5 148.4
Viscosity Index – ASTM D-2270 137 137 153 136 134
SPGR – ASTM D-1298 0.8393 0.8408 0.8468 0.8550 0.8602
Density – ASTM D-1298 6.989 7.001 7.051 7.119 7.163
Flash Point °C (°F) – ASTM D-92 264 (507) 254 (489) 253 (487) 264 (507) 254 (489)
Fire Point °C (°F) – ASTM D-92 278 (532) 280 (536) 280 (536) 276 (529) 274 (525)
Pour Point °C (°F) – ASTM D-97 -53 (-63) -48 (-54) -40 (-40) -45 (-49) -42 (-44)
Four-Ball Wear Test – ASTM D-4172 (40 kg, 1200 rpm, 75° C, 60 min.) 0.45 0.45 0.45 0.45 0.45
Copper Strip Corrosion Test – ASTM D-130 1A 1A 1A 1A 1A
Rust Test – ASTM D665 A & B Fresh Water and Synthetic Sea Water Pass Pass Pass Pass Pass
Foam, ml (ASTM D-892) Sequence I, II, III Test End – and After 10 minutes settling 0/0/0 0/0/0 0/0/0 0/0/0 0/0/0
Demulsibility ASTM D-1401 [oil/water/cuff (minutes)] 40/40/0 (5) 40/40/0 (5) 40/40/0 (5) 40/40/0 (5) 40/40/0 (5)

 

WordPress Tags: Synthetic,Compressor,tools,shop,AMSOIL,Series,life,lubricant,technology,protection,times,petroleum,maintenance,disposal,temperatures

Synthetic PC Series Compressor Oils SAE 10W
(PCH)
 SAE 20
(PCI)		 SAE 30
(PCJ) 		SAE 40
(PCK)		 SAE 50
(PCL)
ISO VG – ASTM D-2422 32 46 68 100 150
VK 100°C – ASTM D-445 6.2 7.3 10.9 13.6 17.9
VK 40°C – ASTM D-445 33.1 42.4 67.4 100.5 148.4
Viscosity Index – ASTM D-2270 137 137 153 136 134
SPGR – ASTM D-1298 0.8393 0.8408 0.8468 0.8550 0.8602
Density – ASTM D-1298 6.989 7.001 7.051 7.119 7.163
Flash Point °C (°F) – ASTM D-92 264 (507) 254 (489) 253 (487) 264 (507) 254 (489)
Fire Point °C (°F) – ASTM D-92 278 (532) 280 (536) 280 (536) 276 (529) 274 (525)
Pour Point °C (°F) – ASTM D-97 -53 (-63) -48 (-54) -40 (-40) -45 (-49) -42 (-44)
Four-Ball Wear Test – ASTM D-4172 (40 kg, 1200 rpm, 75° C, 60 min.) 0.45 0.45 0.45 0.45 0.45
Copper Strip Corrosion Test – ASTM D-130 1A 1A 1A 1A 1A
Rust Test – ASTM D665 A & B Fresh Water and Synthetic Sea Water Pass Pass Pass Pass Pass
Foam, ml (ASTM D-892) Sequence I, II, III Test End – and After 10 minutes settling 0/0/0 0/0/0 0/0/0 0/0/0 0/0/0
Demulsibility ASTM D-1401 [oil/water/cuff (minutes)] 40/40/0 (5) 40/40/0 (5) 40/40/0 (5) 40/40/0 (5) 40/40/0 (5)

Share
Posted on December 9, 2011 by , 2 comments

Fire Department Counts on AMSOIL Synthetic Lubricants

Get a FREE Amsoil Catalog

Amsoil

Amsoil

Direct Jobber Craig Hamrick of Macomb, Ill. has been a firefighter in charge of fleet maintenance for 23 years. “My wife and I have been Dealers since 2006 and became Dealers after seeing the impressive results AMSOIL demonstrated in the fire department fleet,” Hamrick said. The fire department is a commercial account of Dealer Glenn Mike Arnold, Hamrick’s sponsor. “We have used Amsoil lubricants since 2003 in the fleet,” Hamrick said. The department has 11 vehicles and numerous small engines and generators, all running with Amsoil products. “Glenn’s knowledge of Amsoil products has helped us select the right products for our needs. Every vehicle in our fleet has AMSOIL installed from front to back.” AMSOIL Powers Generator The Macomb Fire Department generator at the main station is an Onan 150KW unit that is powered by a Cummins QSB 6.7 liter diesel. The generator is equipped with an AMSOIL Duel Remote By-Pass System and Ea Full-Flow and By-Pass Filters. For ease of oil sampling, there is a petcock on one of the ports on the filter housing. The engine is filled with AMSOIL  premium API CJ-4 5W-40 Synthetic Diesel Oil (DEO). “The reason for choosing Premium 5W-40 over AMSOIL Premium 15W-40 Synthetic Diesel Oil (DME) is the slightly better flow characteristics of the 5W-40 for cold-weather startup,” Hamrick said. “While this unit has a block heater to keep the coolant warm, the oil can still be fairly cold. This generator must go from stopped to running with full electrical load in less than one minute. The cold flow characteristics of AMSOIL diesel oil provide maximum protection and peace of mind for me and our department.”

Get a FREE Amsoil Catalog

The fuel is also treated with AMSOIL Diesel Concentrate plus Cold Flow Improver at each fill-up. “The savings are substantial,” Hamrick said. “We only change oil based on oil analysis now, where before we changed every three months or 250 hours. Fleet uptime is one of the most important benefits for us.  Our equipment must respond and perform at maximum capability every time. The generator is just as important.” Oil Analysis Proves AMSOIL Benefits. Hamrick said he was a skeptic of extended drain intervals when he first was approached about AMSOIL synthetics. However, he soon learned the saving potential of AMSOIL synthetic lubricants. The department saves money through the reduction of waste oil generated, as well as fewer costs for equipment repairs and services, both in time and labor.

Get a FREE Amsoil Catalog

The department regularly sends oil samples to OIL ANALYZERS as part of its maintenance program. “The proof is in all of the oil analysis reports,” he said. “We can see by the results.” AMSOIL lubricants are especially well-suited to emergency service vehicles where every second counts. “You never know when you’re going to get that call, and there isn’t a lot of extra equipment available,” Hamrick said. “We need our equipment to be ready and able to perform.”
Even during the winter months, the generator has “instant oil pressure” when it’s fired up, he said. “If you walk into
our station all you will see in our maintenance room is AMSOIL products.” Growing His Own AMSOIL Business
Hamrick specializes in commercial accounts because his background is in heavy-duty diesel equipment. Name recognition of AMSOIL has improved in the years since he became a Dealer. “AMSOIL is easier to sell now
than even when I started as a Dealer,” Hamrick said. He credited AMSOIL INC. for its work building AMSOIL brand recognition in numerous markets. His experience with the products also helps him with other fleet managers as he tells them his first-hand experience of AMSOIL cost savings, equipment performance and longevity. “It’s all about saving money and extending the life of the equipment,” Hamrick said.

Share
Posted on November 20, 2011 by , 2 comments

AMSOIL PRODUCTS PREPARE EQUIPMENT FOR TOUGH WINTER WEATHER

Amsoil – Free Amsoil Catalog

AMSOIL PRODUCTS PREPARE EQUIPMENT FOR TOUGH WINTER WEATHER

Free Amsoil Catalog shipped to you door.

The fall months are the time to place boats, motorcycles and lawn care equipment into storage and prepare snowmobiles, snowblowers and other vehicles for the coming winter.

Amsoil

AMSOIL products are formulated to provide maximum protection for engines and fuel systems during storage, while Amsoil synthetic motor oils’ low pour points provide superior cold-temperature protection and performance in two-and four-stroke winter equipment.

 

Fall Storage Protection

Gasoline can break down in as little as 60 days, causing varnish and gums that clog injectors, fuel lines and carburetors, leading to poor engine performance and starting problems. In many applications, draining the fuel system can be impractical, and doing so can expose the system to corrosion on the bare metal in the tank and fuel system and cause gasket and seal cracking.

AMSOIL Gasoline Stabilizer reduces the oxidation that occurs when fuel is store for extended periods, improving performance, extending equipment life and decreasing maintenance expenses.Amsoil
During storage, fluctuations in ambient temperatures can form condensation within the engine that can cause surface corrosion on cylinder liners, piston rings, anti-friction bearings and steel/iron contact surfaces on rotational seals. Long periods of storage can also dry out cylinders, often resulting in permanent damage when the equipment is dry-started in the spring.

AMSOIL Engine Fogging Oil offers superior film retention, providing long-term protection against corrosion and dry starts, extending engine life and reducing operating expenses. Its aerosol spray formulation offers easy and clean application, while reaching more components and offering complete distribution of the oil, something especially beneficial in applications with horizontal cylinder orientation, such as outboard motors.

Winter Four-Stroke Performance 

Conventional oils thicken in the cold, which can result in inadequate lubrication to critical engine parts at cold start-up, or even prevent the engine from starting.
AMSOIL Formula 4-Stroke Power Sports Synthetic Motor Oil provides serious protection and performance in four-stroke engines, including ATVs and snowmobiles. Its broad 0W-40 viscosity rating effectively protects in both hot and cold temperature extremes.
AMSOIL Formula 4-Stroke Synthetic Small Engine Oil provides exceptional protection in the severe-service conditions common in both gasoline-and diesel-fueled small engines including welders, skidsteers, compressors, snowblowers and more. It remains fluid at sub-zero temperatures for superior cold-weather protection.
Winter Two-Stroke Performance
AMSOIL DOMINATOR and INTERCEPTOR
Synthetic 2-cycle Oils provides exceptional performance in snowmobiles and other two-stroke equipment. Amsoil DOMINATOR is formulated with heavier base oils for “on the edge” operation, while also protecting pistons and bearings subjected to the rigors of extreme riding.
AMSOIL INTERCEPTOR is engineered specifically for power-sports applications and engines equipped with exhaust power valves. It contains the finest synthetic base oils and additives for exceptional cleanliness, while controlling exhaust valve sticking and providing outstanding overall lubrication.
Gasoline Additive
AMSOIL Quick shot SE is formulated to thoroughly clean varnish, gums and insoluble debris in two-and four-stroke gasoline-powered small engines and power sports equipment fuel systems, restoring peak performance. Amsoil Quickshot effectively addresses performance issues related to ethanol, water and dirty pump gas, while stabilizing fuel between uses and during short-term storage periods. Use Amsoil for fewer fuel related problems and better winter performance.

http://www.syntheticoilhq.com

 

Share
Posted on November 19, 2011 by , Reply
First « 12