Home » Posts tagged "operation"

AMSOIL Motorcycle Octane Boost (MOB)

AMSOIL Motorcycle Octane Boost

AMSOIL Motorcycle Octane Boost

 

AMSOIL Motorcycle Octane Boost

Maximizes Power and Efficiency

image

FREE Amsoil Catalog

AMSOIL Motorcycle Octane Boost (MOB) increases octane for power and efficiency. It is designed to improve startup performance and eliminate engine ping and knock for increased power at low-rpm operation. Motorcycle Octane Boost contains detergents that help combustion chambers and fuel delivery systems maintain cleanliness for optimum performance. At the recommended treat rate, it does not harm catalytic converters or oxygen sensors and is compatible with all other AMSOIL fuel additives.

Maximizes Power & Performance
When treated at 1.3 oz. per gallon of fuel, MOB increases the octane of gasoline up to three numbers. Increased octane improves power and can eliminate performance-robbing and potentially damaging engine knock or ping (see below).

Motorcycle Octane Boost

Improves Low-rpm Performance
Engine knock is especially noticeable in some motorcycles during idle or low-rpm operation and high-temperature driving. Most modern bikes are equipped with sophisticated knock-detection systems that can alter spark timing and the air-to-fuel mixture until knock ceases. Although these systems protect the engine from damage, they can also cause reduced horsepower and poor low-rpm operability. AMSOIL MOB helps reduce the need for knock-detection systems to compensate, ensuring maximum low-rpm power and performance in modern bikes.

Cleans Harmful Deposits
Because Motorcycle Octane Boost contains active detergents, it can help maintain efficiency. For clean up, however, AMSOIL recommends treating gasoline with AMSOIL Quickshot®, which contains a greater concentration of cleaning agents.

What is engine knock and why does it matter?
The tendency of a hydrocarbon fuel, such as gasoline, to knock is measured by its octane number. Lower numbers denote a greater knock tendency; higher numbers denote greater knock control. “Engine knock” is a reference to the sound made from an uncontrolled and early ignition of fuel in the combustion chamber. It causes a knocking or pinging sound, robs the engine of power and can cause catastrophic engine damage. Knock may be eliminated by increasing the fuel’s octane.

What is Research Octane Number?
Research Octane Number (RON), Motor Octane Number (MON) and Anti-Knock Index (AKI) are the three most common octane ratings. AKI, the rating with which most North American motorists are familiar, is typically displayed on gas pumps as the average of the fuel’s RON and MON [(R+M)/2]. RON, however, is the most common industry rating. Therefore, AMSOIL uses the RON rating when conducting performance tests and product validation. Gasoline’s RON generally is a few numbers higher than the AKI posted on the gas pump (e.g. 87 octane fuel, or regular pump gas, has a RON of about 91-92).

 Motorcycle Octane Boost

image

 

When marketing their products, some additive manufacturers have adopted a points system where 10 points equals one octane number. A claim that an additive increases octane 30 points translates into an increase of three octane numbers. This approach is often used only to artificially strengthen marketing claims and is not endorsed by AMSOIL.

Treat Rate
One 4-oz. bottle of AMSOIL Motorcycle Octane Boost treats four to six gallons of gasoline. Slight overtreatment causes no issues,

APPLICATIONS
Motorcycle Octane Boost is primarily recommended for use in four-stroke air- or liquid-cooled motorcycles manufactured by Harley-Davidson®, Yamaha®, Honda®, Ducati®, BMW®, Triumph® and all other four-stroke motorcycles. It may be used in off-road applications, including ATVs, UTVs and snowmobiles, as an alternative to AMSOIL DOMINATOR® Octane Boost. Note: Clean spills immediately using a clean towel. If left standing, Motorcycle Octane Boost can stain painted or metal surfaces. If cleaned immediately, there is no need for concern.

AMSOIL,Motorcycle,Octane,Boost,efficiency,performance,engine,operation,combustion,chambers,systems

Share
Posted on July 26, 2012 by , 5 comments

When is It Hot Enough for a Synthetic Oil?

When is It Hot Enough for a Synthetic Oil?

Synthetic Oil

Synthetic Oil

“My supplier is pushing hard to move his synthetic gear oils into my operation. His position is that the units run too hot for long-term use of mineral oils. At what temperature should I switch to a Synthetic Oil lubricant for a non-circulated gearbox?”

First, the term synthetic is very broad, so we assume you are referring to lubricants that are formulated using polyalphaolefin (PAO) synthetic oil base.

Synthetic Oil

There is no single temperature point that dictates a time to move to synthetics. The decision is dependent on equipment continuous loads and shock loads, equipment availability for routine maintenance, criticality of the application, component life cycles, lubricant life cycles and failure modes among other things.

Generally, the rate of lubricant degradation doubles with every 18 degrees F increase in temperature. Once formulated with antioxidant additives, PAO-based lubricants have a lower baseline rate of oxidative degradation. At low temperatures, a PAO’s increased oxidative life may not be noticeable, particularly if you have to change the oil at some point for other reasons. At higher temperatures, the synthetic may last noticeably longer.

Typically, you begin to notice the extra life provided by a PAO synthetic oil above 160 degrees F. If it is above 180 degrees F, and especially 200 degrees F, the difference in oxidative life becomes quite apparent. However, the point at which a change to synthetic is justified is dependent perhaps on a handful of additional “program management” parameters such as:

1. Do you intend to run your gear oils with an appropriate use of filtration and oil analysis to support life-cycle extensions for many years?

2. Are you currently doing oil analysis and performing condition-based changes?

3. Do you have, and have you communicated to your lab, oxidation limits that flag impending oxidation problems?

4. Does the machine’s operating temperature vary a great deal (a PAO’s high viscosity index enables it to operate across a wider temperature range)?

5. Do you have an effective contamination control program in place that will enable you to fully exploit the PAO’s extended life?

With the appropriate management strategy, a change to a high-performance product can actually cost considerably less than the equivalent mineral oil product type. Outside of these considerations, somewhere around 165 degrees F represents the point at which you probably should begin to consider the use of synthetics for the sake of lubricant longevity, if not for the sake of reliability.

Synthetic Oil

Synthetic Gear Oil

WordPress Tags Synthetic Oil Synthetic Oil: Enough,Synthetic,FREE,Amsoil,catalog,Noria,Corporation,gear,supplier,operation,mineral,temperature,lubricant,decision,equipment,maintenance,component,life,failure,degradation,Once,difference,management,analysis,cycle,oxidation,problems,machine,index,contamination,strategy,performance,product,cost,Outside,units,cycles,modes,degrees,temperatures,parameters,extensions,lubricants,synthetics,oxidative,sake

Share
Posted on January 11, 2012 by , Reply

AMSOIL PRODUCTS PREPARE EQUIPMENT FOR TOUGH WINTER WEATHER

Amsoil – Free Amsoil Catalog

AMSOIL PRODUCTS PREPARE EQUIPMENT FOR TOUGH WINTER WEATHER

Free Amsoil Catalog shipped to you door.

The fall months are the time to place boats, motorcycles and lawn care equipment into storage and prepare snowmobiles, snowblowers and other vehicles for the coming winter.

Amsoil

AMSOIL products are formulated to provide maximum protection for engines and fuel systems during storage, while Amsoil synthetic motor oils’ low pour points provide superior cold-temperature protection and performance in two-and four-stroke winter equipment.

 

Fall Storage Protection

Gasoline can break down in as little as 60 days, causing varnish and gums that clog injectors, fuel lines and carburetors, leading to poor engine performance and starting problems. In many applications, draining the fuel system can be impractical, and doing so can expose the system to corrosion on the bare metal in the tank and fuel system and cause gasket and seal cracking.

AMSOIL Gasoline Stabilizer reduces the oxidation that occurs when fuel is store for extended periods, improving performance, extending equipment life and decreasing maintenance expenses.Amsoil
During storage, fluctuations in ambient temperatures can form condensation within the engine that can cause surface corrosion on cylinder liners, piston rings, anti-friction bearings and steel/iron contact surfaces on rotational seals. Long periods of storage can also dry out cylinders, often resulting in permanent damage when the equipment is dry-started in the spring.

AMSOIL Engine Fogging Oil offers superior film retention, providing long-term protection against corrosion and dry starts, extending engine life and reducing operating expenses. Its aerosol spray formulation offers easy and clean application, while reaching more components and offering complete distribution of the oil, something especially beneficial in applications with horizontal cylinder orientation, such as outboard motors.

Winter Four-Stroke Performance 

Conventional oils thicken in the cold, which can result in inadequate lubrication to critical engine parts at cold start-up, or even prevent the engine from starting.
AMSOIL Formula 4-Stroke Power Sports Synthetic Motor Oil provides serious protection and performance in four-stroke engines, including ATVs and snowmobiles. Its broad 0W-40 viscosity rating effectively protects in both hot and cold temperature extremes.
AMSOIL Formula 4-Stroke Synthetic Small Engine Oil provides exceptional protection in the severe-service conditions common in both gasoline-and diesel-fueled small engines including welders, skidsteers, compressors, snowblowers and more. It remains fluid at sub-zero temperatures for superior cold-weather protection.
Winter Two-Stroke Performance
AMSOIL DOMINATOR and INTERCEPTOR
Synthetic 2-cycle Oils provides exceptional performance in snowmobiles and other two-stroke equipment. Amsoil DOMINATOR is formulated with heavier base oils for “on the edge” operation, while also protecting pistons and bearings subjected to the rigors of extreme riding.
AMSOIL INTERCEPTOR is engineered specifically for power-sports applications and engines equipped with exhaust power valves. It contains the finest synthetic base oils and additives for exceptional cleanliness, while controlling exhaust valve sticking and providing outstanding overall lubrication.
Gasoline Additive
AMSOIL Quick shot SE is formulated to thoroughly clean varnish, gums and insoluble debris in two-and four-stroke gasoline-powered small engines and power sports equipment fuel systems, restoring peak performance. Amsoil Quickshot effectively addresses performance issues related to ethanol, water and dirty pump gas, while stabilizing fuel between uses and during short-term storage periods. Use Amsoil for fewer fuel related problems and better winter performance.

http://www.syntheticoilhq.com

 

Share
Posted on November 19, 2011 by , Reply