Home » Posts tagged "transmission"

AMSOIL SYNTHETIC LUBRICANTS INCREASE FUEL ECONOMY 6.54 PERCENT

imageAMSOIL SYNTHETIC LUBRICANTS
INCREASE FUEL ECONOMY
6.54 PERCENT IN DIESEL
TRUCKING APPLICATIONS1

FREE Amsoil Catalog

For a copy of this study, ask for it in the catalog request form!

Use this link for all Amsoil heavy trucking products on one page.

Industry-Standard Testing

image

To determine the fuel economy benefits of its synthetic lubricants, Amsoil conducted the industry-standard SAE J1321 In-Service Fuel Economy Test Procedure.
First, the baseline rate of fuel consumption was determined for two nearly identical Kenworth® T800B diesel trucks and 53’ trailers from Ford® Motor Company’s* Rawsonville, MI fleet. Texaco brand conventional lubricants were installed in each vehicle’s engine, transmission, and front and rear differentials. Both trucks simultaneously completed runs on a 40-mile test route representative of real-world driving conditions beginning and ending at Ford’s Rawsonville fleet maintenance facility.
Fuel consumption was recorded from each vehicle’s engine control module (ECM)
following each run. Although both vehicles were operated using the same conventional
lubricants and according to the same procedures, the test truck consumed an average
of 0.37 more gallons of fuel per run compared to the control truck.

 

image

 

The test truck alone was then thoroughly flushed of its conventional lubricants prior to
installing AMSOIL synthetic lubricants. Both trucks simultaneously completed runs on
the test route according to the same procedures used during the baseline segment. Fuel
consumption data was again recorded from the ECMs. The switch to AMSOIL synthetic
lubricants eliminated the 0.37-gallon difference in fuel consumption per baseline
segment run, resulting in 6.54 percent improved fuel economy.

image

 

WordPress Tags: AMSOIL,SYNTHETIC,LUBRICANTS,INCREASE,FUEL,ECONOMY,PERCENT,benefits,industry,Service,Test,Procedure,consumption,Kenworth,Ford,Motor,Company,Rawsonville,fleet,Texaco,vehicle,engine,transmission,Both,world,maintenance,module,Although,procedures,truck,trailers,differentials,vehicles,trucks

Share
Posted on December 26, 2011 by , Reply

Family Handyman Magazine Gets it Right on Synthetic Oil Myths – almost : Amsoil Engine Flush.

Amsoil Engine Flush

Family Handyman magazine

Family Handyman Magazine had a short tip on the 4 Big Synthetic Oil Myths. www.familyhandyman.com

The big four myths listed were;

  1. You have to flush the engine before you can run synthetic oil in it. FALSE. You should NEVER flush your engine. All carmakers warn against this practice. (editorial comment; this is the one reaction we disagree with)
  2. Synthetic oil causes leaks. FALSE. This was true 25 years ago. Not anymore. Current formulations contain seal conditioners to prevent leaks.
  3. Once you switch to synthetic, you can’t go back to regular oil. FALSE. No truth whatsoever to this one.
  4. Since synthetic oil flows better when cold, I can ignore the manufacturer’s recommendations for 5W- 20 and use 10W-30. FALSE. Heavier weight oil reduces fuel efficiency and can mess up valve timing mechanisms. Stick with the manufacturer’s oil weight recommendations.

Amsoil Engine Flush

In general, Family Handyman gets it straight on these tips. These have each been a long standing myth so it’s good to get a major magazine to clear the air. We agree with their reaction to tips 2,3, and 4.

Engine Flush

Amsoil has sold an engine flush product for years. In many cases, it’s not needed. However, in certain cases it’s a proper product to use to transition a car to synthetic oil. It’s been used in thousands of vehicles by thousands of Amsoil customers with no issues.

Amsoil Engine Flush

Amsoil Engine Flush AMSOIL Engine and Transmission Flush (FLSH) helps restore fuel economy, increase operating efficiency and reduce emissions in gasoline and diesel engines, and automatic transmissions. Its potent, detergent-based formula cleans sludge and deposit build-up, promoting lower operating temperatures and reduced oil consumption. AMSOIL Engine and Transmission Flush is safe on parts and can be easily disposed of with waste oil. Amsoil Engine Flush

Restores Vehicles to Like-New
New engines and transmissions run more efficiently, but over time they gather harmful deposits that cause power and performance loss. Stop-and-go driving, prolonged idling, short trips that do not allow the engine to reach full operating temperature, towing, the ingestion of airborne dirt, fuel dilution, water condensation and oxidized oil all can promote sludge build-up in motor oil and transmission fluid. As it settles, sludge clogs narrow oil passages, restricting oil flow to vital parts, especially the upper valve train area. Amsoil Engine Flush

In transmissions, deposits can form on clutch plates, causing hesitation and erratic shifting. Ultimately clutch glazing can set in, reducing the life of the transmission. Deposits in engines and transmissions can accelerate wear, causing power loss and increased fuel consumption. Amsoil Engine Flush

• Cleans engines and transmissions for improved efficiency, fuel economy and lower emissions
• Prolongs equipment life
• Detergent-based formula more environmentally friendly
• Compatible with seals and gaskets
• One-treatment results
• Easily disposed of with waste oil

Installing new oil or transmission fluid into a dirty vehicle may not be enough to remove deposits and increase efficiency. The detergents and dispersants in some lubricants may not be able to handle leftover sludge and deposits, and the new lubricant soon becomes unfit for service, accelerating the formation of even more harmful deposits. Amsoil Engine Flush

AMSOIL Engine and Transmission Flush Benefits
Unlike many flush products, AMSOIL Engine and Transmission Flush features a multi-use formulation that dissolves and disperses sludge, varnish and deposits in both engines and automatic transmissions. Due to its detergent-based formulation, used AMSOIL FLSH can be easily disposed of with waste oil, making it more user-friendly. Its advanced formula of light base oil technology, powerful detergents and dispersants provides safe cleaning action. AMSOIL FLSH is compatible with both petroleum and synthetic oils, preparing poorly maintained equipment for installation of new oil. It represents the first step toward restoring neglected equipment to top-notch performance. AMSOIL Engine and Transmission Flush provides the following benefits in only one treatment:

Gasoline and Diesel Engines

• Helps loosen sticky valves and rings, minimizing blow-by and reducing emissions
• Helps quiet lifter noise
• Promotes lower operating temperatures through sludge removal
• Easy disposal

Automatic Transmissions

• Cleans deposits in oil cooler and ports
• Helps unclog fluid passages
• Cleans deposits and varnish from clutch plates, helping improve efficiency
• Promotes smoother operation and transmission life through reduced shift delay

Applications
AMSOIL Engine and Transmission Flush is recommended for diesel and gasoline engines, and automatic transmissions. It is not recommended for CVT transmissions or differentials.

Directions for Use
Though it works in one treatment, AMSOIL Engine and Transmission Flush is safe enough to be used at every oil change. If using a flushing machine, follow the manufacturer’s recommendation. Otherwise, use the following guidelines:

Engine: Add 16 oz. bottle of AMSOIL Engine and Transmission Flush to engine oil fill port. Idle the engine for 10-15 minutes, then immediately drain the oil. Ensure enough time for the system to completely
drain. Remove and replace the engine oil filter. Refill engine with new engine oil in the viscosity grade recommended by the manufacturer.

Transmission: Engage emergency brake. Add 16 oz. bottle of AMSOIL Engine Flush to transmission oil fill port. Idle for 10-15 minutes; shift through drive and reverse. Do NOT place vehicle under heavy load. Drain entire transmission and torque converter of fluid. FILTER MUST BE CHANGED prior to refilling with new transmission fluid.

NOTE: It is not recommended to flush transmissions that do not have a removable pan or access to the transmission filter.

 

Amsoil Engine Flush

Amsoil Engine Flush

 

 

 

 

 

 

 

(above) Automatic transmission clutch plates pre-cleanup. Varnish and glazing is heavy on some of the plates.

Amsoil Engine Flush

Amsoil Engine Flush

 

 

 

 

 

 

 

(above) Automatic transmission clutch plates after cleanup with AMSOIL Engine Flush reveal lighter glazing and varnish.

Amsoil Engine Flush

Amsoil Engine Flush

 

 

 

 

 

 

 

(above) Cylinder head pre-cleanup. Note the sludge deposits on and around the valve springs and push rod openings.

Amsoil Engine Flush

Amsoil Engine Flush

 

 

 

 

 

 

 

(above) Cylinder head after cleanup with AMSOIL Engine Flush. The valve springs and push rod openings are noticeably cleaner, with fewer sludge deposits. The manufacturer’s stamping is more easily seen.

http://www.syntheticoilhq.com

Diesel fuel treatment

WordPress Tags: Handyman,Magazine,Synthetic,Myths,engine,FALSE,editorial,reaction,Current,Once,truth,manufacturer,Heavier,efficiency,valve,Stick,tips,myth,Flush,Amsoil,product,cases,transition,customers,Transmission,FLSH,gasoline,formula,sludge,consumption,performance,Stop,temperature,ingestion,dirt,dilution,condensation,area,plates,hesitation,life,equipment,Detergent,Compatible,treatment,results,vehicle,lubricant,formation,Benefits,products,features,user,technology,action,petroleum,installation,Diesel,Engines,rings,lifter,noise,removal,Easy,disposal,Automatic,operation,Directions,Though,machine,recommendation,Otherwise,guidelines,bottle,port,Idle,Ensure,system,Remove,Refill,Engage,emergency,Drain,FILTER,NOTE,cleanup,Varnish,Cylinder,recommendations,mechanisms,vehicles,emissions,transmissions,temperatures,ports,differentials,thousands,detergents,dispersants,formulation

Share
Posted on December 9, 2011 by , 2 comments

AMSOIL Provides Complete Vehicle Cold-Weather Performance

Click here for FREE Amsoil catalog!

Amsoil

Amsoil synthetic oil works better in extreme cold. Extreme cold can cause conventional motor oil, transmission fluid and gear lube to thicken, starving vital moving parts of necessary lubrication. In many cases, thick motor oil will prevent vehicles from starting. Cold, thick transmission fluid results in delayed or sluggish shifts and inadequate protection for bearings, valves and other critical parts. Thick gear lube, meanwhile, requires more energy to turn the gears, reducing fuel efficiency. Because gears and bearings in the axle housing are splash-lubricated, conventional gear lubes that are too thick at cold temperatures can starve internal components of lubrication, which can cause excessive wear and premature failure.
Conventional petroleum lubricants thicken because they often contain paraffin (wax). While modern refining techniques remove most of the wax from petroleum oil, some wax-like molecules remain. These wax-like molecules are soluble at ambient temperatures above freezing, but crystallize into a honeycomb-like structure at lower temperatures and cause circulation problems. At startup, this can leave working parts unprotected while the lubricant warms to a temperature that allows it to flow. amsoil synthetic lubricants do not contain paraffin. Amsoil synthetic oils provide outstanding low-temperature fluidity for fast, dependable winter starts; quick, responsive shifts and immediate startup protection. Superior Amsoil Fuel & Coolant Additives and Amsoil Diesel applications can be especially sensitive to cold-weather issues. As the temperature drops, the wax naturally found in diesel fuel begins to form
crystals. The point at which wax crystals form is known as the cloud point. These wax crystals eventually clog the fuel filter and starve the engine of fuel, preventing it from starting. While low-quality fuels may form wax crystals in temperatures as warm as 40°F, most fuels have a cloud point near 32°F. The point at which the wax crystals clog the fuel filter is known as the cold filter-plugging point (CFPP). amsoil Cold Flow Improver reduces the CFPP of ultra-low-sulfur diesel fuel by as much as 20ºF for increased protection. In frigid conditions, motorists often idle vehicles for extended periods to warm the interiors and defrost the windows. Not only can the practice be inconvenient, it wastes fuel as well. amsoil Dominator® Coolant Boost uses proprietary tiered-surfactant technology to provide quick and effective heat transfer inside radiator and cylinder heads, resulting in faster engine warm-up times. As a result, vehicle interiors warm more quickly and the defroster becomes effective sooner. Amsoil diesel fuel additive. Amsoil antifreeze. Amsoil fuel addetive.

Amsoil synthetic oil.

Amsiol

Amsiol

 

Technorati Tags: ,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,

Share
Posted on November 21, 2011 by , 5 comments

Harley Davidson Sued for overheating; Or use Amsoil :- Amsoil motorcycle oil.

Amsoil motorcycle oil reduces engine temperatures, and provides protection even in extreme conditions. Get a FREE Amsoil Catalog or view all motorcycle products  on one page.

Harley Davidson Sued

BUY NOW by calling 1-800-956-5695Amsoil motorcycle oil and mentioning referral number 313120

A Federal Court Judge has denied a Harley Davidson motion to dismiss Harley bikers’ claims for fraudulent and unfair business practices, violations of Consumers Legal Remedies Act (CLRA), and unjust enrichment. A class action lawsuit may now go forward against Harley Davidson alleging certain Harley motorcycle engines produce severe, and excessive heat causing burn injuries and clothing to catch on fire.
Valenica, CA (PRWEB) August 06, 2011

Harley Davidson Sued

Last week, a federal judge ruled that a class action lawsuit against Harley Davidson could go forward, siding with four bikers who claim their Harley Davidson motorcycles were defectively designed because their engines ran so hot as to pose a constant danger to riders of being burned and were therefore not fit for their intended use.

Harley Davidson Sued

The complaint alleges that since 1999, Twin Cam 88, 96, 103 and 110 cubic inch engines in Harley motorcycles produce severe, excessive heat causing clothing to catch on fire, burn injuries and the danger of burn injury to riders and passengers as well as overheating causing premature engine wear and in models manufactured after 2006, transmission failure. Although Harley Davidson asked the Eastern District of California court to throw out the claims under state law, the U.S. District Judge sided with the bikers.

Harley Davidson Sued  Harley Davidson Sued  Harley Davidson Sued

Greg Owen, a partner at Los Angeles personal injury attorneys Owen, Patterson & Owen and one of the lawyers representing the plaintiffs in this case, states, “Harley Davidson has known about this problem from the early 2000s and has the technology to fix it, but has chosen to sell tens of thousands of touring bikes here in California without disclosing this known defect. When Harley customers complain to Harley’s dealers after purchase, Harley’s response is that’s normal and it refuses to offer an effective fix to the problem.”

Owen believes the unsafe heat problem is due to Harley selling larger engines that cannot comply with the emission standards of many states, including California.

‘The fix is pretty simple,’ says Owen, “and Harley already has it – manufacture touring bikes with liquid cooled engines instead of air cooled engines. If Harley did that this serious design and safety defect would go away.”

The recent ruling allows the case to move forward, and Harley Davidson will now face Class Action Certification process at the end of the month. image

Amsoil motorcycle oil reduces engine temperatures, and provides protection even in extreme conditions. Get a FREE Amsoil Catalog or view all motorcycle products  on one page.

BUY NOW by calling 1-800-956-5695Harley Davidson Sued and mentioning referral number 313120

Four Sacramento-area riders are suing Harley-Davidson, saying their bikes get dangerously hot. One even says his pants caught fire while riding. Now a class action lawsuit has brought against the motorcycle maker.Read the local story here; http://sacramento.cbslocal.com/2011/06/23/call-kurtis-harley-davidson-lawsuit/

Share
Posted on September 9, 2011 by , Reply

Amsoil Equipped Motorcycles Shine In Fuel Economy Challenge

Amsoil

amsoil

Amsoil

Amsoil Equipped Motorcycles Shine In Fuel Economy Challenge

Amsoil

AMSOIL synthetic lubricants figured prominently in the Vetter Fuel Economy Challenge held May 13 in northern California, where a diesel-powered motorcycle using Amsoil products won by achieving 128.24 mpg. Many of the other bikes also relied on Amsoil products to help achieve results nearly as impressive.

Amsoil

Winning driver Fred Hayes of Hayes Diversified Technologies (Hayes-DT) completed the challenge riding the company’s MD670 F2 diesel-powered motorcycle (pictured above). Hayes bested the next closest competitor by over 18mpg using biodiesel fuel, a lightweight motorcycle design (370 pounds dry) and Amsoil synthetic lubricants throughout.

  • Engine and Transmission – Series 3000 5W-30 Synthetic Heavy Duty Diesel Oil
  • Cooling System – Antifreeze and Engine Coolant, Dominator© Coolant Boost
  • Chassis – Series 2000 Synthetic Racing Grease
  • Chain – MP Heavy Duty Metal Protector
  • Forks – Shock Therapy© Suspension Fluid #10 Medium
  • Fuel – Diesel Concentrate

Competitors completed a 133.5-mile course designed to provide real-world, challenging conditions. The trip, beginning and ending in Carmel, Calif.,

included mountainous terrain cresting a 2,500-foot pass, while the return ride along the famous El Camino Real subjected riders to 30 mph headwinds that tested the limits of each motorcycle’s fuel efficiency. Held at various places throughout the country, the Vetter Fuel Economy Challenge dates to 1980 and aims to encourage development of motorcycle technologies that improve fuel economy while remaining viable for everyday drivers.

The winner must consume the least amount of fuel measured in dollars and cents while meeting all prescribed conditions. Hayes used $4.53 in biodiesel, essentially one gallon, to travel the entire 133.5 miles in challenging conditions, highlighting the bike’s impressive technology and the effectiveness of AMSOIL products. Hayes said his bike showed measurable improvements running Series 3000 5W-30 Synthetic Heavy Duty Diesel Oil and Diesel Concentrate, including easier shifting from the transmission. Competitors had to remain ahead of trailing official at all times to prevent them from padding fuel economy statistics by driving slowly. Two bikes were disqualified for doing so.

AMSOIL-sponsored Hayes-DT focuses on developing the world’s most cutting-edge, heavy-fuel-powered, light tactical vehicles and small engines for military use.

In fact, key Hayes-DT corporate personnel have served in modern military conflicts deployed on Hayes-DT military motorcycles. The bikes receive the most use from the Combat Military Police for rout recognizance and convoy control.

Hayes-DT Street Fighter bike

The Hayes-DT Street Fighter bike achieved 90.82 mpg running biodiesel and AMSOIL lubricants throughout

A second Hayes-DT bike, the Street Fighter, was disqualified after a battery problem caused it to miss the official start. Following repairs, driver Josh Chen rallied to complete the course anyway, achieving 90.82 mpg, which would have been good enough for third place. The Street Fighter used the same lineup of AMSOIL products as the MD670 F2. Although neither motorcycle is available to the general public yet, Hayes-DT is currently working on EPA and EU emissions certification. Until then, competitions like the Vetter Fuel Economy Challenger allow Hayes-DT to showcase the advanced technologies of their bikes and the performance benefits of AMSOIL synthetic lubricants and additives.

http://www.syntheticoilhq.com/catalog

Share
Posted on August 23, 2011 by , 3 comments
12 » Last